Beneficial Nematodes ALL - Application

 Releasing Beneficial Nematodes in your garden or farm is a simple process. You can opt for a standard watering can or select from our range of application tools. Our hose-end sprayer or pump sprayer are ideal for applying nematodes.

ACTIVATED NEMATODE STORAGE

Once activated, introduce within 1 hour. Store activated nematodes for no longer than 6 hours.

HOSE-END SPRAYER INSTRUCTIONS

We've compiled detailed measurements for each of our hose-end sprayers. 

APPLICATION RESTRICTIONS

When applying beneficial nematodes, pressure should not exceed 72 PSI. Nozzle diameter must be 0.8mm or larger.

Use room temperature water and let nematodes sit for 15 minutes to allow powder to completely dissolve. 

3 EASY INTRODUCTION METHODS:
WATERING CAN, PUMP SPRAYER, OR HOSE-END SPRAYER
Nematodes are not a chemical, so their effectiveness will not be reduced by the amount of water used to create the release solution. Adjust the concentration of the solution based on the extent of the pest infestation and the size of area to be treated.
  • Introduce indoors at any time, or outdoors in the morning, evening, or on a cloudy day.
  • Avoid direct sunlight. Beneficial Nematodes are susceptible to UV light.

WATERING CAN & PUMP SPRAYERS:


PREPARE:
  • Moisten the soil to improve habitat. Keep soil moist for two weeks after application.
  • Avoid run-off.
ACTIVATE:
  • Mix nematodes with 1-5 gallons of water (59-69°F) to cover the desired area.
  • Dilute to create volume needed for coverage of area.
APPLY SOLUTION:
  • Introduce nematodes onto desired area. Don't be concerned if every inch isn't covered as these organisms will move throughout the soil.
  • Use within 6 hours of activation.
WATER:
  • Water treated area immediately after application. Keep soil moist for two weeks. Avoid run-off.
  • Keep soil temperature between 44-86°F.



HOSE-END SPRAYERS:

Remove filter if applicable. Walk slowly and evenly across the target area, making sure to cover the entire surface.

Use room temperature water and let nematodes sit for 15 minutes to allow powder to completely dissolve. 


INSTRUCTIONS:
  1. Add the appropriate amount of nematodes and water to reservoir.
  2. Attach the hose-end sprayer to the water source and turn on the water.
  3. Twist knob at the top of the hose-end sprayer to ON.
  4. Apply nematode mix to desired area.
RELEASE:
50 million nematodes
  1. Divide nematodes into thirds.
  2. Fill water reservoir to 15 gallon mark.
  3. Mix 1/3 of nematodes in water reservoir and spray until empty to release.
  4. Repeat three times or until entirety of nematode packaging is used.
25 million nematodes
  1. Divide nematodes into half.
  2. Fill water reservoir to 15 gallon mark.
  3. Mix 1/2 of nematodes in water reservoir and spray until empty to release.
  4. Repeat twice or until entirety of nematode packaging is used.
10 million nematodes
  1. Dump all nematodes into reservoir.
  2. Fill water to 10 gallon mark.
  3. Apply nematode mix to desired area.
5 million nematodes
  1. Dump all nematodes into reservoir.
  2. Fill water to 5 gallon mark.
  3. Apply nematode mix to desired area.
To learn more about our hose-end sprayer, click here.


OTHER HOSE-END SPRAYERS:

If sprayer has a screen filter, please remove.
Application measurements may vary depending on sprayer type and nematode species. Please see our application charts in our photos.


INSTRUCTIONS:
  1. Dump all nematodes into reservoir.
  2. Fill water to 32 ounce mark.
  3. Set dial level to appropriate setting.
  4. Apply nematode mix to desired area.
INTRODUCE:
50 million nematodes set dial level to:
Preventative / Light - 4 tsp.  
Moderate / Heavy - 5oz.

25 million nematodes set dial level to: 
Preventative / Light -  1.5oz. 
Moderate / Heavy - 8oz. 

10 million nematodes set dial level to:
Preventative / Light - 4oz.
Moderate / Heavy - 8oz.  

5 million nematodes set dial level to: 
Preventative / Light - 4oz. 
Moderate / Heavy - 8oz.